718 お客様のコメント
質問 1：
The attempt to manage an Ethernet Routing Switch (ERS) 8000 using a VRRP address was unsuccessful.
What is causing this problem?
A. The virtual router identifier is 0.
B. The incorrect MAC offset is configured for the VRRP address.
C. A real IP address is required for management access not a VRRP address.
D. The datacenter interface is set as a critical IP interface.
正解：C
質問 2：
Which CLI command is used to validate that synchronization for High Availability mode is correct?
A. show ha-sync
B. show ha-all
C. show ha-info
D. show ha-state
正解：C
質問 3：
Source MAC address-based VLANs are an example of which group of VLAN types?
A. MAC based
B. Address based
C. Policy based
D. Weighted
正解：A
解説: (Pass4Test メンバーにのみ表示されます)
質問 4：
Refer to the exhibit.
Simple Loop Prevention Protocol (SLPP) provides active protection against Layer 2 network loops on a per-VLAN basis. For the SLPP Tx process, the network administrator decides on which VLANs to enable SLPP. The hello packets are then replicated out all ports that are members of the SLPP-enabled VLAN.
Given the following information shown in the exhibit:
A = InterSwitch Trunk (IST)
B = Split MultiLink Trunk (SMLT)
# 1 VSP 9000
# 2 VSP 9000
# 3 ERS 4500
When setting up the SLPP Rx process, which configuration role is setup on VSP #1?
A. The VSP # 1 Rx process is enabled on all SMLT VLANs to monitor for the VSP # 2 SLPP packets.
B. The VSP #1 Rx process is enabled on all SMLT VLANs to monitor for the ERS #3 SLPP packets.
C. The VSP #1 Rx process is enabled on port 3/1 and the IST ports to monitor for the VSP #2 SLPP packets.
D. The VSP # 1 RX process is enabled on port 3/1 to monitor VSP # 1 and VSP #2 SLPP packets.
正解：C
質問 5：
Refer to the exhibit.
While troubleshooting your VSP 9000 system, you run the command flight-recorder all
1. The associated files ace created.
Based on the information in the exhibit, where are the associated files stored?
A. Internal flash
B. TFTP Server
C. External flash
D. USB Flash device
正解：A
質問 6：
The Key Health Indicators (KHI) feature of Avaya Virtual Services Platform 9000 provides a subset of health information that allows for quick assessment of the overall operational state of the device. The show khi forwarding commands are the way to view this health information.
What kinds of slots are the show khi forwarding commands valid for?
A. GbE slots
B. CP slots
C. IO slots
D. SF slots
正解：C
質問 7：
After experiencing issues with XFPs, the show sys pluggable-optical-modules info CLI command is used to find the switch that does not recognize the XFPs.
What is another method that can be used to view the XFP compatibility?
A. Check for port alarms.
B. Ensure that the config sys is set for pluggable-optical-module info.
C. Show the DWDM-XFP {detail}.
D. Select Edit, Port, General, DDI/SFP from the Enterprise Device Manager.
正解：A
The attempt to manage an Ethernet Routing Switch (ERS) 8000 using a VRRP address was unsuccessful.
What is causing this problem?
A. The virtual router identifier is 0.
B. The incorrect MAC offset is configured for the VRRP address.
C. A real IP address is required for management access not a VRRP address.
D. The datacenter interface is set as a critical IP interface.
正解：C
質問 2：
Which CLI command is used to validate that synchronization for High Availability mode is correct?
A. show ha-sync
B. show ha-all
C. show ha-info
D. show ha-state
正解：C
質問 3：
Source MAC address-based VLANs are an example of which group of VLAN types?
A. MAC based
B. Address based
C. Policy based
D. Weighted
正解：A
解説: (Pass4Test メンバーにのみ表示されます)
質問 4：
Refer to the exhibit.
Simple Loop Prevention Protocol (SLPP) provides active protection against Layer 2 network loops on a per-VLAN basis. For the SLPP Tx process, the network administrator decides on which VLANs to enable SLPP. The hello packets are then replicated out all ports that are members of the SLPP-enabled VLAN.
Given the following information shown in the exhibit:
A = InterSwitch Trunk (IST)
B = Split MultiLink Trunk (SMLT)
# 1 VSP 9000
# 2 VSP 9000
# 3 ERS 4500
When setting up the SLPP Rx process, which configuration role is setup on VSP #1?
A. The VSP # 1 Rx process is enabled on all SMLT VLANs to monitor for the VSP # 2 SLPP packets.
B. The VSP #1 Rx process is enabled on all SMLT VLANs to monitor for the ERS #3 SLPP packets.
C. The VSP #1 Rx process is enabled on port 3/1 and the IST ports to monitor for the VSP #2 SLPP packets.
D. The VSP # 1 RX process is enabled on port 3/1 to monitor VSP # 1 and VSP #2 SLPP packets.
正解：C
質問 5：
Refer to the exhibit.
While troubleshooting your VSP 9000 system, you run the command flight-recorder all
1. The associated files ace created.
Based on the information in the exhibit, where are the associated files stored?
A. Internal flash
B. TFTP Server
C. External flash
D. USB Flash device
正解：A
質問 6：
The Key Health Indicators (KHI) feature of Avaya Virtual Services Platform 9000 provides a subset of health information that allows for quick assessment of the overall operational state of the device. The show khi forwarding commands are the way to view this health information.
What kinds of slots are the show khi forwarding commands valid for?
A. GbE slots
B. CP slots
C. IO slots
D. SF slots
正解：C
質問 7：
After experiencing issues with XFPs, the show sys pluggable-optical-modules info CLI command is used to find the switch that does not recognize the XFPs.
What is another method that can be used to view the XFP compatibility?
A. Check for port alarms.
B. Ensure that the config sys is set for pluggable-optical-module info.
C. Show the DWDM-XFP {detail}.
D. Select Edit, Port, General, DDI/SFP from the Enterprise Device Manager.
正解：A
Higuchi -
早速試験に受けで、ほんとに合格できましたよ！嬉しいすぎます。今回の6103の問題集の内容もすごくわかりやすくて素敵です。