LCP-001 全真模擬試験 DEMO

問題5: You are installing Linux on a workstation for a new employee. Which partition should be
largest?
A. /
B. /boot
C. /lib
D. /usr
正解: D
6. You are about to install a new program on an RPM based Linux system. Which of the following
would be the best way to accomplish this?
A. Get the source code in a tarball and install from that source.
B. Get a source RPM and use rpm to install it.
C. Use rpm to install the program's binaries from an RPM package.
D. Use cpi to extract the binaries from a source RPM and use rpm to install those sources.
正解: C
7. What tool can you use to print shared library dependencies?
A. ldconfig
B. ldd
C. libdep
D. libpath
E. ldev
正解: B
Explanation:
ldd command prints the shared libraries required by each program or shared library specified on the
command line. Example: ldd libdb.so.3 libc.so.6 => /lib/tls/libc.so.6 (0x00237000) /lib/ld-linux.so.2
(0x0021e000)
8. What program is needed to establish a PPP link to another computer?
A. pppd
B. wvdial
C. papd
D. kppp
正解: A
Explanation:
wvdial - PPP dialer with built-in intelligence. wvdial is an intelligent PPP dialer, which means that it
dials a modem and starts PPP in order to connect to the Internet. It is something like the chat(8)
program, except that it uses heuristics to guess how to dial and log into your server rather than
forcing you to write a login script.
9. You need to install a fax server. Which type of fax/modem should you install to insure Linux
compatibility?
A. External Serial Fax/modem
B. External USB Fax/modem
C. Internal ISA Fax/modem
D. Internal PCI Fax/modem
正解: A
10. You are running Linux 2.0.36 and you need to add a USB mouse to your system. Which of the
following statements is true?
A. You need to rebuild the kernel.
B. You need to upgrade the kernel.
C. You need to load the USB modules for your existing modular kernel.
D. USB support is no available in Linux.
正解: B
11. If Linux detects an ACPI BIOS on bootup, what does it automatically deactivate?
A. PnP
B. PCI
C. ATA
D. APM
正解: D
12. Where can lilo place boot code?
A. The boot ROM
B. The boot RAM
C. The /boot partition
D. The MBR on a hard drive
正解: D
13. The lspci command can display information about devices except the following:
A. Card bus speed (e.g. 66Mhz)
B. Card IRQ settings
C. Card vendor identification
D. Card AGP rate (e.g. 1x, 2x, 4x)
E. Card Ethernet MAC address
正解: E
Explanation:
lspci is a utility for displaying information about all PCI buses in the system and all devices
connected to them. To display the MAC address of Ethernet, we use the ifconfig command.
14. What command would help you identify the I/O address range being used by the network
card?
A. cat/proc/modules
B. cat/proc/devices
C. cat/proc/meminfo
D. cat/io/dma
E. cat/proc/ioports
正解: E
15. You have just upgraded your PC to a 60 gigabyte IDE drive. While partitioning the drive, you
notice that only 32 gigabytes are available. Which of the following will most likely allow you to use
the entire drive?
A. Create two smaller partitions of 30 gigabytes each.
B. Set the PC BIOS to use LBA mode.
C. Create a partition that resides entirely below the first 1024 cylinders.
D. Use GRUB or the latest version of LILO as a bootloader.
E. Upgrade the PC BIOS to the latest version available.
正解: E
16. While installing from source code you don't see the configuration script. What command can
you run to compile the code?
A. make configure
B. install
C. install makefile
D. make
正解: D
Explanation:
The purpose of the make utility is to determine automatically which pieces of a large program need
to be recompiled, and issue the commands to recompile them. example C programs, since they are
most common, but you can use make with any programming language whose compiler can be run
with a shell command. In fact, make is not limited to programs. You can use it to describe any task
where some files must be updated automatically from others whenever the others change. To
prepare to use make, you must write a file called the makefile that describes the relationships
among files in your program, and the states the commands for updating each file. In a
program,typically the executable file is updated from object files, which are in turn made by
compiling source files. So, make command compile the source code.