923 お客様のコメント
質問 1：
When installing a conveyor tunnel, antennas should be placed:
A. underneath the conveyor with radiation patterns overlapping in the area under the conveyor.
B. around the conveyor with radiation patterns overlapping away from the conveyor path.
C. on the same side of the conveyor with radiation patterns not overlapping away from the conveyor path.
D. around the conveyor with radiation patterns overlapping along the conveyor path.
正解：D
質問 2：
A network connected interrogation zone is not reporting reads, even though operators are passing goods through the zone. The system administrator has no contact with the operators at the zone. Which of the following would be the FIRST step to take when troubleshooting this interrogator remotely?
A. Ping the interrogator.
B. Use original equipment manufacturer (OEM) software to connect to the interrogator.
C. Restart the interrogator.
D. Send maintenance to replace the interrogator.
正解：A
質問 3：
In a conveyor application, which of the following would be MOST important for getting consistent reads?
A. Adding an additional interrogator to increase coverage.
B. Angling the antennas to increase the time the tag is in the interrogation zone.
C. Slowing down the conveyor until the read rate is acceptable.
D. Speeding up the conveyor.
正解：B
質問 4：
When firmware upgrades become available, which of the following should the technician consider FIRST?
A. The benefits of new upgrade.
B. How to install the upgrade.
C. Whether the upgrade can be downloaded from the internet.
D. When to schedule the upgrade.
正解：A
質問 5：
Which of the following RFID tags would be BEST for inconspicuous tagging of assets containing a maximum of eight bytes of data and are inductively coupled?
A. Passive 13.56 MHz tag that is affixed to the asset and camouflaged requiring continuous loop interrogation.
B. Passive Gen 2 tag requiring line of sight backscatter interrogation.
C. Active 433.92 MHz tag with strategically installed fixed interrogators.
D. Active 433.92 MHz tag requiring modulated backscatter interrogation.
正解：A
質問 6：
After viewing a site diagram, it is observed that the location of one of the interrogation zones is bisected by a steel door. Which of the following problems could this cause?
A. If the door is closed, the interrogation area is reduced by one-half.
B. Tags on the other side of the closed door would be read more than once.
C. With the doors closed, the signal strength would overload the interrogator.
D. Having steel doors amplifies the interrogator signal.
正解：A
When installing a conveyor tunnel, antennas should be placed:
A. underneath the conveyor with radiation patterns overlapping in the area under the conveyor.
B. around the conveyor with radiation patterns overlapping away from the conveyor path.
C. on the same side of the conveyor with radiation patterns not overlapping away from the conveyor path.
D. around the conveyor with radiation patterns overlapping along the conveyor path.
正解：D
質問 2：
A network connected interrogation zone is not reporting reads, even though operators are passing goods through the zone. The system administrator has no contact with the operators at the zone. Which of the following would be the FIRST step to take when troubleshooting this interrogator remotely?
A. Ping the interrogator.
B. Use original equipment manufacturer (OEM) software to connect to the interrogator.
C. Restart the interrogator.
D. Send maintenance to replace the interrogator.
正解：A
質問 3：
In a conveyor application, which of the following would be MOST important for getting consistent reads?
A. Adding an additional interrogator to increase coverage.
B. Angling the antennas to increase the time the tag is in the interrogation zone.
C. Slowing down the conveyor until the read rate is acceptable.
D. Speeding up the conveyor.
正解：B
質問 4：
When firmware upgrades become available, which of the following should the technician consider FIRST?
A. The benefits of new upgrade.
B. How to install the upgrade.
C. Whether the upgrade can be downloaded from the internet.
D. When to schedule the upgrade.
正解：A
質問 5：
Which of the following RFID tags would be BEST for inconspicuous tagging of assets containing a maximum of eight bytes of data and are inductively coupled?
A. Passive 13.56 MHz tag that is affixed to the asset and camouflaged requiring continuous loop interrogation.
B. Passive Gen 2 tag requiring line of sight backscatter interrogation.
C. Active 433.92 MHz tag with strategically installed fixed interrogators.
D. Active 433.92 MHz tag requiring modulated backscatter interrogation.
正解：A
質問 6：
After viewing a site diagram, it is observed that the location of one of the interrogation zones is bisected by a steel door. Which of the following problems could this cause?
A. If the door is closed, the interrogation area is reduced by one-half.
B. Tags on the other side of the closed door would be read more than once.
C. With the doors closed, the signal strength would overload the interrogator.
D. Having steel doors amplifies the interrogator signal.
正解：A
宫沢** -
本当に急に買いまして三日後に受験して受かったってっ感じ
とっつきやすいように構成されています。だから超安心で試験に受かる